440.951.6022 phone    
3900 Ben Hur Avenue, Suite 10
Willoughby, Ohio 44094
440.951.6012 fax
home
BASWAphon
finishes
technical data
installation
LEED
  photo gallery
projects
locate a rep
locate an installer
contact us

BASWAphon     

 

BASWAphon Frosted Finish
Frosted, Seamless Sound Absorptive Acoustical Finish System

General

This “Frosted“ System has the lowest installed cost with the following advantages:

  1. The “Frosted” System has BASWAphon’s “light sand” finish. The “light sand” finish hides many minor imperfections in the finished surface, especially with critical lighting. The NRC Rating for the “Frosted” 30-mm System is 0.75, the “Frosted” 40-mm System is 0.80 and the “Frosted” 68-mm System is 0.85.

  2. Up to 5,000 s.f. can be installed in one continuous surface.

  3. The “Frosted” System consists of a factory pre-coated “supporting” panel (a bonded mineral wool backing coated with glass “micro-spheres”), a trowel applied Base 407 coat (coarse marble aggregate in a proprietary emulsion) and a spray applied “Frost” Coat (fine marble aggregate in a proprietary emulsion).

  4. The “Frosted” System can be curved in one or two directions very easily for a nominal cost increase.

  5. The “Frosted” System can be integrally pigmented to match any color, including black or other deep, dark colors.

  6. Touch-up of the “Frosted” System should be performed by a qualified BASWAphon Technician, however on-site personnel can be easily trained to perform most required repairs.

  7. The “Frosted” System is not water soluble. The “Frosted” finish surface is very durable and can be washed, even “scrubbed” with a brush and rinsed with clean water to remove most stains.

Special features

  • finest surface structure

  • intense coloration

  • curved surfaces


System set-up

 

BASWAphon – Classics

  1. Spray applied BASWAphon "Frost" Coat

  2. Trowel applied BASWAphon 407 Base Coat

  3. Pre-Coated BASWAphon Supporting Panel

  4. BASWAphon Adhesive

  5. Stable Substrate
 

BASWAphon Classic Finish
Smooth, Seamless Sound Absorptive Acoustical Finish System

General


This “Classic” System continues to set the aesthetic and acoustical standard for all seamless acoustical products with the following properties:

  1. The “Classic” System is BASWAphon’s premium product with a smooth hand troweled finish. Inherent with any hand troweled product, slight variations or imperfections in the finished surface may be visible with critical lighting. The NRC Rating for the “Classic” 30-mm System is 0.75, 40-mm System is 0.80, the “Classic” 68-mm System is 0.857.

  2. Up to 5,000 s.f. can be installed in one continuous surface.

  3. The “Classic” System consists of a factory pre-coated “supporting” panel (a bonded mineral wool backing coated with glass “micro-spheres”), a trowel applied Base 407 coat (coarse marble aggregate in a proprietary emulsion) and a trowel applied Top Coat (fine marble aggregate in a proprietary emulsion).

  4. The “Classic” System can be curved in one or two directions with relative ease at a minor cost increase.

  5. The “Classic” System can be integrally pigmented to match any “pastel” to “medium deep” color (where deep colors are specified, the “Frosted” System is recommended).

  6. Touch-up and cleaning of the “Classic” System must be performed under the direction of a qualified BASWAphon Technician. The Top Coat of the “Classic” System will “activate and soften” with prolonged exposure to water.

Special features

  • finest surface structure

  • intense coloration

  • curved surfaces


System set-up

 

BASWAphon – Classics

  1. Trowel applied BASWAphon Top Coat

  2. Trowel applied BASWAphon 407 Base Coat

  3. Pre-Coated BASWAphon Supporting Panel

  4. BASWAphon Adhesive

  5. Stable Substrate

BASWAphon Clean Finish
Thick Smooth, Seamless Sound Absorptive Acoustical Finish System

General

The “Clean“ System is a specialty product that is highly resistant to moisture, mold and mildew, with a cost comparable to the “Classic“ System. It is applied on ceiling surfaces of indoor swimming pools, protected exterior spaces or other high moisture applications. This System has the following attributes:

  1. The “Clean“ System has a slightly granular smooth hand troweled finish . Inherent with any hand troweled product, slight variations or imperfections in the finished surface may be visible with critical lighting. The NRC rating for the “Clean“ 30mm System is 0.75, for the “Clean“ 40-mm System is 0.80 and the “Clean“ 68-mm System is 0.85.

  2. Up to 5,000 s.f. can be installed in one continuous surface.

  3. The “Clean“ System consists of a factory pre-coated supporting panel (a bonded mineral wool backing coated with glass micro-spheres ), a trowel applied Base 407 coat (coarse marble aggregate in a proprietary emulsion) and a trowel applied Finish Coat (coarse marble aggregate in a proprietary emulsion).

  4. The “Clean“ System can be curved in one or two directions with relative ease at a minor cost increase.

  5. The “Clean“ System can be integrally pigmented to match any pastel to medium deep color.

  6. Touch-up and cleaning of the “Clean“ System must be performed under the direction of a qualified BASWAphon Technician.

  7. The “Clean“ System is very durable and can be washed, even scrubbed with a brush and rinsed with clean water to remove most stains.

Special features

  • finest surface structure

  • intense coloration

  • curved surfaces


System set-up

 

BASWAphon – Classics

  1. Trowel applied BASWAphon 407 Finish Coat

  2. Trowel applied BASWAphon 407 Base Coat

  3. Pre-Coated BASWAphon supporting panel

  4. BASWAphon Adhesive

  5. Stable Substrate
 
     

Baswaphon acoustical

Baswaphon acoustical

Sound Solutions

Sound solutions

baswa

Baswaphon acoustical

3900 Ben Hur Avenue, Suite 10, Willoughby, Ohio 44094
Phone: (440) 951-6022  |  Fax: (440) 951-6012


BASWAphon is a product of BASWA AG of Switzerland. © 2008 Sound Solutions Construction Services, LLC